|
CYBEX PG 400 PERSONAL GYM
|
|
A More Powerful Way To Exercise
- Precise biomechanices match the body's motion.
- Durable components, proven in thousands of commercial facilities worldwide.
- Easy-to-use adjustments make your workout fly by.
- Sleek style and compact footprint fits any room.
- Over 30 biomechically correct exercises, with no changeovers.
Overall dimensions: 105" x 82" x 83" or 82" x 72" (when stored)
Weight Stack: 235 lb.
|
|
CYBEX PG 400 GENERAL SPECIFICATIONS
|
Correct biomechanics and ergonomic design let you work every muscle group, comfortably and effectively. Over 30 exercises in all.
 |
INTERESTING FACT -
Al Pacino recently donated six single station units of fitness equipment to charity and replaced them with one Cybex PG400. Nice choice, Al!
Thanks to our extensive research, you can be sure your workout is biomechanically correct. |
Frame Finish
- Shall be made of mechanical quality steel purchased in mill run quantities to assure the best consistency.
- Prior to applying finish, each part shall be put through a multi-stage wash to remove all oils and to chemically prepare the surface for maximum adhesion. After the wash, the frames shall be dried and coated with an electrostatically applied powder coat finish which shall be applied in powder form and then baked until cured.
- The finish shall be textured and very hard, assuring a scratch and chip resistant finish.
Weight Selection
- Weights are to be selected by using a high quality selector pin which completely penetrates the weight plate and locks in place to eliminate any chance of disengaging the pin during use. The pin shall be attached to the weight stack with a plastic lanyard in order that the pin stays with the machine.
Weight Stack Configuration
- Graduated weight stack shall be a combination of 3" x 12" x 1" and 4" x 12" x 1" weight plates, weighting 9 lbs. and 12 1/2 lbs. respectively.
Increment Weight
- A 4.5 lb. plastisol covered increment weight is standard. A hanger for the increment weight shall be incorporated into the frame of the machine.
Weight Plates
- Shall be made of cold-rolled steel with wrinkle black powder coat finish.
- Guide rod holes shall be machined to a tolerance of .006 inches.
Weight Plate Bushings
- Self aligning low-friction bushings shall surround the guide rods for smooth gliding motion.
Pulleys
- Shall use Dupont Corp. fiberglass-reinforced nylon material, tensile strength rated at 22,500 PSI with double sealed bearings.
- Pulleys shall be 4.50 inches in diameter with a cable groove with a depth of .250 inches.
Weight Transport
- Shall be lubricated, 7 x 19, 1/8" galvanized steel, nylon coated aircraft cable with breaking strength rated at 2000 pounds.
- All cable ends shall be finished off with a swaged fitting with a breaking strength exceeding that of the cable itself.
Weight Stack Guide Rods
- Shall be solid ground and polished cold-drawn steel with minimum yield strength of 100,000 PSI with a hard chrome plated piston steel finish with an overall minimum accuracy of .010.
Weight Stack Suspension
- Shall have heavy-duty neoprene bumpers with an 80-durometer rating under the weight stacks to reduce shock and vibration stresses to the frame and facility.
Handgrips
- Shall be closed-end PVC closed cell foam vinyl sleeve.
Frame Construction
- Primarily 1 1/2 x 2" tubing with 11 gauge wall thickness or 2" tubing with 11 gauge wall thickness but different tubing and wall thickness shall be used as required through engineering stress analysis.
- Fully welded frames for maximum structural integrity and minimum maintenance.
- All machining and welding must be done utilizing jigs and fixtures to insure highest quality and interchangability of parts.
Hardware
- All 3/8" button head cap screws shall be of grade 5 (or equivalent). All socket head cap screws shall be of grade 8 (or equivalent). All bolts shall be zinc plated for additional corrosion resistance.
Weight Stack Guards
- All weight stacks shall be guarded either by the machine frame or shield to prevent bystanders from inadvertent contact with the weight stack during use.
Cushion/Upholstery
- A superior grade of Naugahyde from Gencorp shall be used on all pad covers and wear covers.
- The color shall be sulfide stain resistant.
- All edges shall be stitched to eliminate any folds in the material that would limit durability.
- Cushions come with replaceable slipcovers on all high use areas, reducing maintenance expense by not having to replace the entire cushion.
- Cushion foam consists of a combination of high and medium density closed-cell Omalon polyurethane, for durability and comfort.
- Meets ASTM MVSS302 and California Technical Bulletin 117 standards for flammability. Depending on the application, densities vary between 2.35 and 6 lbs./cu. ft.
Adjustments
- Recessed high contrast decal for all seat and pad adjustments for maximum readability.
Instructional Wall Poster
- Shall provide step-by-step instructions for the positioning and movement.
- Wall poster shall indicate proper positioning and muscles trained.
|
|
